Lehrstuhl für Fertigungstechnologie, Universität Erlangen-Nürnberg



Systematics of the extended characterisation of advanced and ultra high strength automotive steels



Project Status: finished

Members


The project is running in partnership with the AUDI AG as an INI.FAU cooperation. The intention is the application of advanced characterisation methods at high strength steel grades. Currently the workability of these grades cannot be fully ensured by the conventional characterisation methods in a sufficient way. Bending loads could not be determined for example by tensile test and forming-limit-curve – although components consist of higher strength steels are often exposed on bending-dominant plastic forming. Several test methods are used to detect the forming capacity adequate and to utilise the potential of new steel grades. Furthermore the knowledge should be integrated into the post processing of forming simulation. This can be achieved by compare the critical stresses on test specimens and on components within the simulation.


  


Research Groups


Publications

    2012

    • Hezler, C.; Merklein, M.; Hecht, J.; Griesbach, B.:
      Identification of Process-Based Limit Stress States Applying a Stretch-Bending-Test.
      Key Eng. Mater. 504-506(2012), pp. 47-52

    • Hezler, C.; Tsoupis, I.; Merklein, M.; Kasparbauer, M.:
      Experimental determination of stress limit curves - comparison of applied technological tests and stamped components by fractographic examinations.
      In: Hora, P. (Edtr.): Proc. 5th Forming Technology Forum, Institute of Virtual Manufacturing, ETH Zurich, 2012, pp. 87-92

    • Hezler, C.; Kaupper, M.; Merklein, M.; Kasparbauer, M.:
      Investigation of influencing parameters on the shape of experimentally determined stress limit curves.
      In: Tewari, A; Narasimhan, K.; Date, P. (Edtrs.): Proceedings IDDRG2012, Indian Institute of Technology Bombay, 2012, pp. 566-573

    2011

    • Hezler, C.; Kopp, C.; Bader, M.; Griesbach, B.; Merklein, M.; Russ, F.:
      Characterisation of the transition area at partial hot stamped car body components by the 3-point bending test.
      In: Wieland, H. (Edtr.): Proceedings SCT2011, Verlag Stahleisen GmbH, 2011, pp. 280-287

    • Kopp, C.; Griesbach, B.; Bader, K.-M.; Freudenberg, P.; Hezler, C.; Russ, F.:
      Optimization on Hot-Forming Technologies - New Tool Designs and Alternative Heating Technologies for Tailored Properties.
      In: Kollek, R. (Edtr.): Proceedings Tools and Forming, Verlag der TU Graz, 2011, pp. 181-189

    2010

    • Merklein, M.; Hezler, C.; Kopp, C.; Hecht, J.; Schaller, L.:
      Kennwertermittlung für Streck-Biege-Beanspruchungen.
      In: M. Pohl (Edtr.): Proceedings Tagung Werkstoffprüfung, Stahleisen GmbH, 2010, pp. 253-258

    2009

    • Kopp, C.; Schaller, L.; Jessen, B.; Merklein, M.; Hezler, C.:
      Charakterisierung des Formänderungsvermögens von hoch- und höchstfesten Karosseriestählen mit dem 3-Punkt Biegeversuch - Einfluss der Probenpräparation.
      In: Borsutzki, M.; Geisler, S. (Edtrs.): Tagungsband Werkstoffprüfung 2009, Stahleisen GmbH, 2009, pp. 87-92

    Letztes Update: 03.05.2012