Lehrstuhl für Fertigungstechnologie, Universität Erlangen-Nürnberg



Priv.Doz. Dr.-Ing. Dipl.-Inf. Hinnerk Hagenah



Egerlandstr. 13, 91058 Erlangen
Tel.: 09131/85-20838
Fax: 09131/85-27141
Mail address: This e-mail address is being protected from spambots. You need JavaScript enabled to view it

Executive Director DFG Transregional Collaborative Research Center 73
Member of the DFG Collaborative Research Center 814
Member of the Board of Directors of ESAFORM
Member of the Graduate School of Advanced Optical Technologies
Member of the Center for Management Technology and Society (CMTS)



Projects


Publications

    2018

    • Lorenz, R.; Hagenah, H.; Merklein, M.:
      Influence of the Coating Process on the Tribological Conditions during Cold Forging with a MoS2 Based Lubricant.
      AIP Conference Proceedings; https://doi.org/10.1063/1.5034867 1960(2018)1, pp. 040013

    • Lorenz, R.; Hagenah, H.; Merklein, M.:
      Experimental evaluation of cold forging lubricants using double cup extrusion tests.
      Materials Science Forum 918(2018), pp. 65-70

    • Hagenah, H.; Scharrer, H.; Lechner, M.; Merklein, M.:
      4.0 in metal forming - questions and challenges.
      Procedia CIRP (2018), accepted

    • Papke, T.; Huber, F.; Hagenah, H.; Schmidt, M.; Merklein, M.:
      Potentiale der Kombination von Umformtechnik und additiver Fertigung in hybriden Prozessketten.
      In: Drummer, D. (Edtr.): 6. Industriekolloquium des Sonderforschungsbereichs 814 - Additive Fertigung, Print Line, 2018, pp. 59-76

    2016

    • Merklein, M.; Hagenah, H.:
      Introduction to sheet-bulk metal forming.
      Production Engineering 10(2016)1, pp. 1-3

    • Purr, S.; Wendt, A.; Meinhardt, J.; Moelzl, K.; Werner, A.; Hagenah, H.; Merklein, M.:
      Data-driven inline optimization of the manufacturing process of car body parts.
      IOP Conf. Series: Materials Science and Engineering 159(2016)1, pp. 012002

    2015

    • Hagenah, H.; Merklein, M.; Lechner, M.; Schaub, A.; Lutz, S.:
      Determination of the mechanical properties of hot stamped parts from numerical simulations.
      Procedia CIRP 33(2015), pp. 167-172

    • Merklein, M.; Duflou, J.; Leacock. A.; Micari, F.; Hagenah, H. (Edtr.):
      Sheet Metal 2015, Proceedings of the 16th international conference on sheet metal.
      Trans Tech Publ., 2015

    • Hagenah, H.; Geiger, M.:
      Laser Adjustment Using Actuators.
      In: A. Erman Tekkaya, Werner Homberg, Alexander Brosius (Edtr.): 60 Excellent Inventions in Metal Forming, Springer, 2015, pp. 167-172

    2014

    • Plettke, R.; Vipavc, D.; Grüner, M.; Hagenah, H.; Merklein, M.:
      The influence of the annealing process in the fabrication of helical needles for the suture in deep wound cavities.
      Int. J. Computer Integrated Manufacturing 27(2014)10, pp. 960-967

    • Tsoupis, I.; Hildering, S.; Hagenah, H.; Merklein, M.:
      Werkstoffschädigung in der Prozesskette Schneiden - Biegen.
      In: Liewald, M.; Tekkaya, A. E. (Edtrs.): 17. Workshop Simulation in der Umformtechnik, Institut für Umformtechnik, Universität Stuttgart, 2014, pp. 73-89

    • Merklein, M.; Franke, J.; Hagenah, H. (Edtr.):
      WGP Congress 2014, Progress in Production Engineering.
      Trans Tech Publ., 2014

    2013

    • Hagenah, H.; Böhm, W.; Breitsprecher, T.; Merklein, M.; Wartzack, S.:
      Modelling, Construction and Manufacture of a Lightweight Robot Arm.
      Procedia CIRP 12(2013), pp. 211-216

    • Lechner, M.; Kuppert, A.; Hagenah, H.; Merklein, M.:
      Optimization of the heat treatment layout and blank outline of THTB.
      Key Eng. Mater. 554-557(2013), pp. 2465-2471

    • Merklein, M.; Hagenah, H.; Kaupper, M.; Schaub, A.:
      Mechanical response of Ti-6Al-4V alloy on deformation at moderate temperatures.
      Key Eng. Mater. 549 (2013), pp. 311-316

    • Merklein, M.; Hagenah, H.; Kaupper, M.; Schaub, A.:
      Analysis of the deformation behavior of Ti-6Al-4V at elevated temperatures.
      Key Eng. Mater. 554-557 (2013), pp. 29-32

    • Merklein, M.; Hagenah, H.; Lechner, M.; Kuppert, A.:
      Simulationsgestützte Auslegung maßgeschneiderter wärmebehandelter Aluminiumhalbzeuge.
      In: Tekkaya A. E.; Liewald M. (Edtrs.): 16. Workshop Simulation in der Umformtechnik, Institut für Umformtechnik und Leichtbau, Technische Universität Dortmund, 2013, pp. 90-101

    • Hagenah, H.; Geiger, M.; Merklein, M.:
      Numerical simulation to improve robustness in sheet metal forming process chains.
      AIP Conf. Proc. 1532(2013), pp. 683 - 688

    • Merklein, M.; Franke, J.; Hagenah, H. (Edtr.):
      WGP Congress 2013, Progress in Production Engineering.
      Trans Tech Publ., 2013

    • Merklein, M.; Hagenah, H.; Schneider, T.:
      Sheet-Bulk Metal Forming Processes - State of the Art and its Perspectives.
      In: Kolleck, R. (Edtr.): TTP 2013 - Tools and Technologies for Processing Ultra High Strength Materials, Verlag der TU Graz, 2013, pp. 197-204

    • Merklein, M.; Hagenah, H.; Schneider, T.:
      Blechmassivumformung - Stand der Technik und Ausblick.
      In: Merklein, M.; Behrens, B. A., Tekkaya, A. E. (Edtrs.): 2. Workshop Blechmassivumformung, Meisenbach, 2013, pp. 1-10

    2012

    • Li, H.; Dong, X.; Shen, Y.; Zhou, R.; Diehl, A.; Hagenah, H.; Engel, U.; Merklein, M.; Cao, J.:
      Analysis of microbending of CuZn37 brass foils based on strain gradient hardening models.
      J. Mater. Process. Technol. 212(2012)3, pp. 653-661

    • Li, H.; Dong, X.; Huang, S.; Diehl, A.; Hagenah, H.:
      Material Intrinsic Length in Plastic Strain Gradient Theory and Microbending Process of Metal Foils.
      Adv. Mater. Res. 403-408(2012), pp. 685-690

    • Merklein, M.; Hagenah, H. (Edtr.):
      Proc. 15th ESAFORM Conference Part 1 & 2.
      Trans Tech Publications, 2012

    • Merklein, M.; Allwood, J. M.; Behrens, B.; Brosius, A.; Hagenah, H.; Kuzman, K.; Mori, K.; Tekkaya, E.; Weckenmann, A.:
      Bulk forming of sheet metal.
      Annals of the CIRP 61(2012)2, pp. 725-745

    • Plettke, R.; Vipavc, D.; Grüner, M.; Hagenah, H.; Merklein, M.:
      Prototype Manufacturing of Helical Needles for Suture in Deep Wound Cavities.
      In: E. Ceretti, A. Fiorentino, L. Giorleo, C. Giardini (Edtr.): Proc. 1st Int.Conf. Design and Processes for medical devices PROMED, NEOS EDIZIONI srl, 2012, pp. 191-194

    2011

    • Li, H.; Dong, X.; Wang, Q.; Shen, Y.; Diehl, A.; Hagenah, H.; Engel, U.; Merklein, M.:
      Determination of material intrinsic length and strain gradient hardening in microbending process.
      International Journal of Solids and Structures 48(2011)1, pp. 163-174

    • Li, H.; Dong, X.; Wang, Q.; Shen, Y.; Diehl, A.; Hagenah, H.; Engel, U.; Merklein, M.:
      Size effects of CuZn37 brass foil in microforming.
      Material Science and Technology 19(2011)4, pp. 15-19

    2010

    • Li, H. Z.; Dong, X. H.; Shen, Y.; Diehl, A.; Hagenah, H.; Engel, U.; Merklein, M.:
      Size effects on springback behaviors due to plastic strain gradient hardening in microbending process of pure aluminum foils.
      Journal of Materials Science and Engineering A 257(2010)16-17, pp. 4497-4504

    • Plettke, R.; Vatter, P.; Vipavc, D.; Cojutti, M.; Hagenah, H.:
      Investigation on the Process Parameters and Process Window of "Three-Roll-Push-Bending".
      In: Hinduja, S.; Li, L. (Edtrs.): Proc. 36th Matador Conf., Springer, 2010, pp. 25-28

    • Li, H.; Dong, X.; Huang, S.; Diehl, A.; Hagenah, H.:
      Material intrinsic length in plastic strain gradient theory and microbending process of metal foils.
      In: (Edtr.): 6th International conference on MEMS NANO, and Smart Systems (ICMENS 2010), 2010, pp. 218-211

    • Hagenah, H.; Vipavc, D.; Plettke, R.; Merklein, M.:
      Numerical Model of Tube Freeform Bending by Three-Roll-Push-Bending.
      In: Associacao Portuguesa de Mecanica Teória, Aplicada e Computacional (Edtrs.): 2nd International Conference on Engineering Optimization, 2010, published on CD

    • Hagenah, H.; Vipavc, D.; Vatter, P.; Cojutti, M.; Plettke, R.:
      Creation of the Data Base for the Process Design of the Three-Roll-Push Bending Process.
      In: Teti, R. (Edtr.): 7th CIRP Int. Conf. Intelligent Computation in Manufacturing Engineering, 2010, pp. 259-264

    2009

    • Merklein, M.; Hagenah, H.; Cojutti, M.:
      Investigations on Three-Roll Bending of Plain Tubular Components.
      Key Eng. Mater. 410-411(2009), pp. 325-334

    • Geiger, M.; Plettke, R.; Hagenah, H.:
      Multi-Objective Optimization of Actuator System Design for Laser Micro Adjustment.
      Production Engineering 3(2009)2, pp. 181-188

    • Plettke, R.; Hagenah, H.; Geiger, M.:
      Application of genetic algorithms for the optimisation of actuator systems for laser micro adjustment..
      International Journal of Microstructure and Materials Properties (IJMMP) 4(2009)6, pp. 615-625

    • Cojutti, M.; Vipavc, D.; Hagenah, H.; Merklein, M.:
      An innovative approach for the process design for three-roll bending of plain tubular components.
      In: Angeles Gutierrez, M.; Sedlmaier, A.; Galdós, L. (Edtrs.): Proc. 1st Int. Congress on Roll Forming, 2009, pp. 133-139

    • Li, H. Z.; Dong, X. H.; Shen, Y.; Diehl, A.; Hagenah, H.; Engel, U.; Merklein, M.:
      Influence of the plasticity strain gradient on springback in micro-bending process of metal foils.
      In: Chinese Society of Mechanical Engineering (Edtr.): Proceedings of The 2nd Asia Conference on micro/nano sized technology (AWMFT-2009), 2009, pp. 602-606

    2008

    • Hagenah, H.; Schmidt, M.; Klämpfl, F.:
      Planning the use of high-power excimer laser for psoriasis treatment.
      In: Mitsuishi, M.; Ueda, K.; Kimura, F. (Edtrs.): Manufacturing Systems and Technologies for the New Frontier - The 41st CIRP Conference on Manufacturing Systems, Springer, 2008, pp. 349-354

    • Geiger, M.; Klämpfl, F.; Hagenah, H.:
      Automated online planning of localized laser process parameters using simulated annealing.
      Production Engineering 2(2008)2, pp. 171-178

    • Klämpfl, F.; Hagenah, H.:
      Algorithmen zum simulationsbasierten, pulsgenauen Planen von Laserbestrahlungen.
      In: Schulze, T.; Preim, B. (Edtrs.): Simulation und Visualisierung 2008. Proceedings of the 19th Conference on Simulation and Visualization (SimVis), SCS Publishing House e.V., 2008, pp. 41-52

    • Klämpfl, F.; Schmidt, M.; Hagenah, H.:
      Intelligent irradiation planning for new laser applications.
      In: De Vin, L. (Edtr.): Proceedings of the 18th International Conference on Flexible Automation and Intelligent Manufacturing (FAIM 2008), Runit AB, 2008, pp. 924-930

    • Merklein, M.; Geiger, M.; Hagenah, H.; Cojutti, M.:
      3-Rollen-Schubbiegen zur flexiblen Herstellung freiformgebogener Rohrleitungen.
      Zukunftstechnologien in Bayern (2008), pp. 24-26

    • Hagenah, H.; Plettke, R.; Klämpfl, F.:
      Fast, problem specific approaches for the evaluation of laser beam propagation in process planning.
      In: Teti, R. (Edtr.): Proceedings of the 6th CIRP International Conference on Intelligent Computation in Manufacturing Engineering, Edizioni Zino, 2008, pp. 413-418

    • Plettke, R.; Hagenah, H.; Geiger, M.:
      Developing a computer aided design system for actuator design for laser micro adjustment.
      In: (Edtr.): Proceedings of the 18th CIRP International Design Seminar (March 2008), 2008, pp. 1-5

    • Hagenah, H.; Plettke, R.; Geiger, M.:
      Algorithms for Planning and Control of Laser Forming.
      In: Vollertsen, F. (Edtr.): Proceedings of the IWOTE 08, BIAS Verlag, 2008, pp. 191-203

    2007

    • Klämpfl, F.; Hagenah, H.:
      Algorithms for pulsewise irradiation planning.
      In: Geiger, M.; Otto, A.; Schmidt, M. (Edtrs.): Proceedings of the LANE 2007, Meisenbach, 2007, pp. 877-886

    • Tang, B. T.; Zhao, Z.; Hagenah, H.; Lu, X. L.:
      Energy based algorithms to solve initial solution in one-step finite element method of sheet metal stamping.
      Comput. Methods Appl. Mech. Engrg. 196(2007), pp. 2187-2196

    • Plettke, R.; Hagenah, H.; Geiger, M.:
      Application of genetic algorithms for the optimization of actuator systems for laser micro adjustment.
      In: Kuzman, K. (Edtr.): Proceedings of the 6th International Conference on Industrial Tools and Material Processing Technologies 2007 (ICIT&MPT 2007), 2007, pp. 297-302

    • Plettke, R.; Hagenah, H.; Geiger, M.:
      Computer assisted design of complex actuator systems for laser micro adjustment.
      In: Geiger, M.; Otto, A.; Schmidt, M. (Edtrs.): Proceedings of the LANE 2007, Meisenbach, 2007, pp. 533-544

    • Plettke, R.; Hagenah, H.; Geiger, M.:
      Computer assisted design of actuator systems for laser micro adjustment.
      Key Eng. Mater. 344(2007), pp. 807-814

    • Plettke, R.; Hagenah, H.; Geiger, M.:
      Rechnergestützter Entwurf von Aktorsystemen für die lasergebundene Mikrojustage.
      In: Schulze, T.; Preim, B.; Schumann, H. (Edtrs.): Simulation und Visualisierung 2007. Proceedings of the 18th Conference on Simulation and Visualization (SimVis), SCS Publishing House e.V., 2007, pp. 43-54

    2006

    • Hagenah, H.; Plettke, R.; Geiger, M.:
      Planning and Control of Laser Forming Applications.
      In: Butala, P.; Hlebanja, G. (Edtrs.): Proceedings of the 39th CIRP International Seminar on Manufacturing Systems, University of Ljubljana, 2006, pp. 359-367

    • Hagenah, H.; Kohlbauer, R.:
      Apllication of fuzzy logic for process design in sheet metal hydroforming.
      In: Govekar, E. (Edtr.): Proceedings of the 9th CIRP International Workshop on Modeling of Machining Operations, University of Ljubljana, 2006, pp. 335-342

    • Klämpfl, F.; Schmidt, M.; Hagenah, H.; Görtler, A.; Wolfsgruber, F.; Lampalzer, R.; Kaudewitz, P.:
      Irradiation planning for automated treatment of psoriasis with a high-power excimer laser.
      In: SPIE (Edtr.): Photonics West 2006: Integrated Optoelectronic Devices , 2006, published on CD

    • Hagenah, H.; Geißdörfer, S.:
      System for the automatic correction of sheet metal bending angles by means of laser beam forming.
      In: Juster, N.; Rosochowski, A (Edtrs.): The 9th International Conference on Metal Forming ESAFORM, Publishing House Akapit, 2006, pp. 235-238

    • Klämpfl, F.; Schmidt, M.; Hagenah, H.; Geiger, M.:
      Algorithms for Irradiation Planning in Medical Laser Applications.
      In: Teti, R. (Edtr.): Proceedings of the 5th CIRP International Seminar on Intelligent Computation in Manufacturing Engineering, University of Naples, 2006, pp. 101-106

    • Geiger, M.; Hagenah, H.:
      Der SFB 396 im Überblick- Beiträge zum Berichts- und Industriekolloquium.
      In: Geiger, M.; Singer, R. F: (Edtrs.): Robuste, verkürzte Prozessketten für flächige Leichtbauteile: Tagungsband zum Industriekolloquium, Meisenbach, 2006, pp. 1-6

    • Hagenah, H.; Plettke, R.; Geiger, M.:
      Planning and Control of Laser Forming Applications.
      In: Butala, P.; Hlebanja, G (Edtrs.): Proceedings of the 39th CIRP International Seminar on Manufacturing Systems, Dept. of Control and Manufacturing Systems, Faculty of Mechanical Engineering, Univ. of Ljubljana, 2006, pp. 359 - 367

    2005

    • Geiger, M.; Hagenah, H.; Hutterer, A.:
      Task Specific Registration Algorithmy within the Closed Loop Control of Laser Forming Processes.
      Production Engineering. Annals of the German Academic Society for Production Engineering 2(2005)7, pp. 125-130

    • Hagenah, H.; Wurm, T.:
      Problem specific design of actuators for micro adjustment.
      Adv. Mater. Res. 6-8(2005), pp. 271-278

    • Hagenah, H.; Wurm, T.; Geiger, M.:
      Computer assisted design of actuators for high precision adjustment in micro technology.
      In: Bramley, A.; Brissaud, D.; Coutellier, D.; Mcmahon, C (Edtrs.): Advances in Integrated Design and Manufacturing in Mechanical Engineering, Springer, 2005, pp. 403-416

    2004

    • Hutterer, A.; Hagenah, H.:
      Correcting non circular dents by means of laser beam forming.
      In: Geiger, M.; Otto, A. (Edtrs.): Laser Assisted Net shape Engineering 4 - Proceedings of the LANE 2004, Meisenbach Verlag, 2004, pp. 1071-1081

    • Hagenah, H.; Kohlbauer, R.; Geiger, M.:
      Knowledge based automated process design using finite element intermediate states.
      In: Teti, R. (Edtr.): Proceedings of the 4th CIRP International Seminar on Intelligent Computation in Manufacturing Engineering. ICME' 2004. Sorrento, Italy, CUES, 2004, pp. 295-300

    • Hagenah, H.; Wurm, T.; Geiger, M.:
      Computer assisted design of actuators for high precision adjustment in micro technology.
      In: Bramley, An.N.; Culley, S.J.; Dekoninck, E.A.; McMahon, C.A.; Medland, A.J.; Mileham, A.R.; Newnes, L.B.; Owen, G.W. (Edtrs.): Proceedings of the 5th International Conference on Integrated Design and Manufacturing in Mechanical Engineering, University of Bath, 2004, pp. 10

    • Geiger, M.; Hagenah, H.; Kohlbauer, R.:
      Computer assisted, knowledge based process design for sheet metal hydroforming using finite element simulation.
      In: Monostori, L. (Edtr.): Enterprises, production networks, University of Budapest, 2004, pp. 67-72

    2003

    • Hutterer, A.; Hagenah, H.; Otto, A.:
      Application of a modified ICP-Algorithm in Manufacturing Technology.
      In: Ertl, T.; Girod, B.; Greiner, G.; Niemann, H.; Seidel, H. (Edtrs.): 8th International Fall Workshop, IOS Press, 2003, pp. 127-134

    • Hutterer, A.; Hagenah, H.; Geiger, M.:
      Development of an irradiation strategy withing a closed loop control system for the laser adjustment of deformation.
      In: The Institute of Control, Automation and Systems Engineers (ICASE) (Edtr.): Proceedings of the 2003 International Conference on Control, Automation and Systems (ICCAS 2003), 2003, pp. 2313-2318

    • Geiger, M.; Wurm, T.; Hagenah, H.:
      Modellierung von Aktoren für das Laserstrahljustieren in der Mikrotechnik.
      In: Hohmann, R. (Edtr.): Fortschritte in der Simulationstechnik, Tagungsband des 17. Symposiums Simulationstechnik ASIM 2003, SCS-Europe, 2003, pp. 261-266

    • Hagenah, H.:
      Simulation based Evaluation of the Accuracy for Sheet Metal Bending caused by the Bending Stage Plan.
      In: Weber, C.; Bley, H.; Hirt, G. (Edtrs.): Proceedings of the 36th CIRP Seminar on Manufacturing Systems, Progress in Virtual Manufacturing Systems, 2003, pp. 513-519

    • Kohlbauer, R.; Hagenah, H.; Geiger, M.:
      Process design for hydroforming of sheet metal pairs using a closed loop controlled finite element simulation.
      In: Shirvani, B.; Geiger, M.; Kals, H.J.J.; Singh, U.P. (Edtrs.): Proceedings of the 10th International Conference on Sheet Metal, SheMet 2003, University of Ulster, 2003, pp. 219-226

    2001

    • Wurm, T.; Menzel, T.; Müller, B.; Hagenah, H.; Geiger, M.:
      The use of kinematic chains and construction catalogues for an advanced design of complex actuator geometries in micro adjustment.
      In: Kjellberg, T. (Edtr.): Proceedings: International CIRP Design Seminar: Design in the New Economy; Design Theory, Methodology and its Intergration with the Computational Tools to support Teams of Competence, KTH Stockholm, 2001, pp. 417-421

    2000

    • Menzel, T.; Hagenah, H.:
      Knowledge Based Approach for Intelligent Design of Manufacturing Processes.
      In: Bothe, H.; Fyfe, C. (Edtrs.): Proceedings of the EIS'2000. Second ICSC Symposium on Engineering of Intelligent Systems, ICSC Academic Press, 2000, pp. 327-333

    • Geiger, M.; Hagenah, H.; Menzel, T.:
      Simulation based optimisation of the accuracy of sheet metal bending parts caused by the manufacturing plan.
      In: Teti, R. (Edtr.): Proceedings of the 2nd CIRP International Seminar of Intelligent Computation in Manufacturing Engineering ICME 2000, 2000, pp. 283-290

    1998

    • Hagenah, H.; Knoblach, J.:
      Bewertung von Fertigungsplänen der Blechverarbeitung in Abhängigkeit von der erreichbaren Bauteilgenauigkeit.
      In: Lehnert, W. (Edtr.): Qualitätsfaktor Umformtechnik: Tagungsband der 5. Sächsischen Fachtagung Umformtechnik in Freiberg, Technische Universität Bergakademie, 1998, pp. 16.1-16.15

    • Hagenah, H.; Backes, F.:
      Computer aided estimation of achievable accuracy for bending parts.
      In: Geiger, M.; Shirvani, B.; Sing, U.P. (Edtrs.): Sheet Metal 1998: Proceedings of the 6th International Conference on Sheet Metal, Twente University Printers, 1998, pp. 199-208